Blog

The Necessity Of Laboratory Exhaust Fume Hoods

August 31, 2015

Laboratory exhaust fume hoods are necessary in all laboratories regardless of the experiments that are being conducted. Every person working in the lab must know they are safe from toxic fumes that may be created during an experiment, and the fume hoods must have a powerful fan that will clear the room in a matter of moments. A fume hood must be installed by a professional, and only special chemical fume hoods can be used in laboratories.

#1: Use The Right Hood

A chemical fume hood is completely different from the hood found in a kitchen, and you must request the right sort of hood before you continue with your installation. A professional installer can help you choose the right hood for your lab, and you must ask the installer where the hood should be placed.

The hood will be attached to a special conduit that leads the gases out of the building, or the hood may be attached to an incinerator that burns off dangerous gases. Special hoods are designed for use with incinerators, and your installer must attach the hood to the incinerator properly. Your lab cannot fill with toxic gases if the hood is in operation, and you can safely dispose of the gases.

#2: Remote Operation

The switch for the hood must be located in the lab, but there must be a separate hood located outside the lab for use by safety personnel. People in the lab may be overcome the fumes, but the hood can be turned on from a remote location. The panel inside the room helps lab workers choose the speed of the fan, the force of the fan and how open the duct is. A small amount of fumes may be disposed of using the lowest settings on the hood, but toxic gases that have built up must be eliminated using the very highest settings on the hood.

#3: How Do You Make Room For The Hood?

The hood you use in your lab must have its own space in the ceiling, and the hood must sit over the most volatile work area in the lab. Perform your most dangerous experiments directly under the hood, and ask your installer if the place where you keep those experiments is a good place for the hood. A wise installer will point you to the right location for the hood, and you may adjust the layout of your lab space accordingly.

#4: How Long Must They Last?

A chemical fume hood will last a very long time if it is cleaned and serviced properly. Every hood must be cleaned properly, and the services must be done on your fume hood every few months. The cleaning for the hood will include a complete adjustment, and there must be a report on the status of the hood. Every person who uses the hoods must have a record of the cleanings, and you should shut down experiments in the lab if the hood is every found to be lacking.

You can keep your laboratory much safer than normal with the use of just one hood, but every sensitive experiment location must have its own hood. The hoods for the lab must be purchased and installed from the same location, and you will benefit from service done by the same technician who did the initial installation. The lab cannot be completely safe without special hoods to pull out toxic gases, and you must consider how your staff will use the hoods when you are in an emergency situation. Proper procedures and equipment will help you run your lab safely and cleanly.

Working in Clean Environments

August 19, 2015

Do you have an application such as inspection of parts or assembly of optics that calls for a clean work environment free from airborne particulate matter? Laminar flow workstations are commonly used for Class 100 (ISO 5) applications that need a level of cleanliness corresponding to less than 100 particles of diameter greater than 0.5 micrometers per cubic foot of air. This type of clean environment is also ideal for the medical, pharmaceutical, electronics, food and industrial sectors for sterile manipulations, assembly of miniature mechanisms, production of optical components.

Laminar Airflow Workstations

Laminar flow workstations provide a source of clean filtered air that flows smoothly over the work area and then out, keeping the working area at the rated cleanliness level. These workstations come in a range of sizes from 24″ wide and 24″ high to as much as 96″ wide by 37″ high, and can be moved through standard-width doorways. The workstations will have:

a flow hood,
both electrostatic and HEPA 99.99% air filters,
micro-controlled low-speed air blowers,
integral lighting over the work area,
electrical outlets for equipment,
surfaces of stainless steel for easy cleaning, or polypropylene to avoid any possible contamination from rust.

The working area is enclosed at the sides to ensure guided airflow and to prevent the possibility of contaminating particles mixing in from the outside. The low blower speed prolongs the fan’s lifetime and also provides a quieter environment for the operator, with noise levels around 65 DBA. Electrical outlets, cable trays and tool drawers are integrated into a complete workstation for a broad spectrum of applications.

These are the basic types of laminar airflow workstations for clean environment applications.

Horizontal Flow Workstation

In a horizontal flow bench, the room air is pulled in from an opening on top of the laminar flow hood or below the work area platform and then prefiltered electrostatically. The air then moves to the rear of the bench and exits through HEPA filters that span the back of the workstation into the working area, after which the ultra-clean Class 100 air exits towards the front of the workstation, and past the operator. The laminar air flow is monitored, and any filter obstruction is reported to the operator. This horizontal flow bench design is intended for product protection.

Such a flow hood could also make an excellent tissue culture hood. Other clean bench applications could be for:

IV admixture preparation,
drug compounding,
plant cell culture,
media preparation,
pharmaceutical procedures,
electronics assembly.

Vertical Flow Workstation

A vertical flow bench design also has the room air pulled in from the top of the laminar flow hood where it is prefiltered electrostatically. In this case, the air then is pulled below through HEPA filters and flowed downward onto the working surface, exiting past the operator at the front. The intended use for this design is in applications that require clean environments and pose no hazard to the operator.

Polymerase Chain Reaction Workstations

Some laminar flow workstations have specialized enclosures that reduce the risk of sample contamination while performing polymerase chain reaction experiments. The constant positive pressure HEPA filtered air prevents airborne contaminants from entering into the work zone. The workstations are equipped with a built-in shortwave UV lamp to effectively decontaminate the work area between amplifications. Safety interlocks prevent operators from being exposed to UV radiation. However, keep in mind that these are not biological safety cabinets. They are designed to provide process protection only from potential airborne contaminants found in the laboratory space.

RDM: Quality, Durability and Cost-Efficiency Combined

August 12, 2015

You may have already heard a lot of good things about RDM and what we have to offer. And honestly, we are quite proud of what people are saying about us…

After all, not every industrial or lab furniture manufacturer out there is given the same accolades or accomplishments that our loyal clients have showered us with.

But come to think of it—what specific aspects makes RDM the real deal?

To answer: It’s because we are able to bring our current and future clients quality, durability and cost-efficiency.

Interested?

Let’s expound:

Durability

When it comes to durable furniture pieces—we are at the top of our game.

Our industrial and lab furniture are made of high-grade, high quality industrial materials, ranging from stainless steel, seasoned wood, and many other essentials. Moreover, we always make it a point that each part of our furniture pieces are fully welded, attached or connected together, to ensure greater durability and strength.

Do you need heavy duty carts? How about work tables for heavy duty applications? We have them all.

Quality

Through our over 37 years experience in the furniture industry, we have become even more versed with regards the ins and outs of manufacturing high quality lab and industrial furniture.

Our manufacturing procedures are designed to bring the utmost efficiency and usability. We have always made sure that our products undergo rigid and strict standards, in order to ensure that our customers get the highest quality they deserve. After all, you deserve nothing less.

Do you want custom furniture for your special needs? Do you want adjustable tables that will fit your specific height requirements? We’ll be more than glad to provide them for you.

Cost Efficiency

In light of our experience in the field—plus the durability and quality of our products—some people presume that our furniture prices and rates are over the roof.

In reality, that’s not the case…

Our aim has been always about providing people real furniture solutions—at reasonable rates. Accordingly, we take pride in putting our customers first before anything else. So, if you do business with us, you can be sure that you’ll be getting your money’s worth. You can rest assured of that.

So, do you need high quality and affordable lab and industrial furniture pieces? Just give us a call. We’ll be more than glad to help.

Money Saving Tips for Your Industrial Furniture Purchases

July 31, 2015

Let’s face it: Buying furniture can mean having to shell out a good amount of money. However, that doesn’t mean you can’t be smart about it.

Fact of the matter is: If you are strategic—you can actually save a lot of money on your industrial furniture pieces.

But how can we make that possible?

Here are the ways:

Tip #1: Be Clear With the Type of Furniture That You Need

There are many types of furniture out there. And chances are, you don’t really need to buy each and every one of them.

In order to know what specific furniture type can help you out—you need to have a clear idea on your needs first.

In other words, you need to know the specific benefits you are looking for.

So for example: Do you want an industrial furniture piece that you can use when working on drafts or reports? If so, then an adjustable table just might be what you need. Or do you need something to store your tools and equipment in? If so, then you can opt for steel or wooden cabinets (depending on your preference).

Tip #2: Know Your Budget

Having a clear and reasonable budget can help prevent you from overspending. Correlatively, this can also help you find the appropriate furniture pieces that you can actually afford.

Tip #3: Know Where (or From Whom) to Get Your Furniture Pieces From

There are different avenues and platforms that you can use to find the furniture piece that you need.

You can go the traditional route and directly visit furniture showrooms. Just remember to engage your “haggling mode” though, to ensure that you get the most out of your money.

If you want, you can also use the virtual platform to buy furniture. Yes—everything is online now—and that includes industrial furniture. But as always, you need to make sure that you’re dealing with a reputable seller, to avoid unwanted issues later on.

Tip #4: Don’t Be Afraid to Ask Questions

If you’ve already found a seller, don’t immediately stop there.

If there are any questions hounding you—don’t hesitate to ask your seller for clarifications. After all, you owe it to yourself to ensure that you’re getting the most appropriate pieces.

What are the materials composing the furniture? What features does it have? Do you customize?

Whatever the question may be—don’t be afraid to ask your seller. This will ultimately help you find the appropriate furniture pieces to invest in, as well as those that can bring the most out of your buck.

Serious Signs That You Need New Furniture

July 21, 2015

Furniture is important to the efficiency of your workplace. As it is, you should be able to determine if your old furniture pieces are still up to par—or if it’s time for a change.

So, how do we know if we need new furniture?

Here are some signs to keep note of:

You Are Not Motivated to Work

When you are not motivated to work, chances are your productivity will take a beating as well. Accordingly, you need to make sure that your amenities (including your furniture) are able to give you that added “boost” for those long work hours ahead.

Tip: Invest in furniture pieces that are designed to help make you more efficient at work. Examples are height adjustable tables, ergonomic chairs and other related pieces. These can help make you and your co-workers more work-ready, and may help increase productivity at the same time.

Increasing Furniture Maintenance and Repair Costs

If you’re constantly bringing your furniture to the “furniture doctor” for repairs, then it might be high time to get new ones. After all, furniture expenses if you add them up—can be quite costly in the long run.

Tip: Make sure to get furniture pieces that are made of durable materials. A good example would be industrial furniture, a furniture type that’s made of industrial-grade materials. These pieces are designed to last—which means they can help you avoid those exorbitantly high furniture maintenance and repairs expenses.

You’re Uncomfortable

If you are just too uncomfortable, then you might want to consider sprucing up your furniture or even your workplace. Working in an uncomfortable work area has been found to have a negative impact on workers—and may even increase the risks for stress.

Tip: Find which particular aspect of your workplace is making you uncomfortable. Afterwards, find a way to turn things around. For example: Is your work table a bit too dilapidated? If so, then you might want to get it repaired, or you can invest in a table that can actually withstand the tasks that you are constantly undertaking.

Just remember though: Don’t invest in a particular furniture piece just because it looks good or it’s comfortable. Make sure that it’s durable and usable as well—for added feasibility and efficiency.

These are just some of the serious signs that you may need new furniture. It’s now up to you to decide if you want to do something about it or not.

5 Costly Mistakes to Avoid When Buying Industrial Furniture

July 13, 2015

Are you planning to buy industrial furniture?

If so, then that would be a good idea. After all, this furniture type can bring a lot of benefits, ranging from durable materials, increased efficiency, feasibility and many others.

It is worthy to note, however, that buying industrial furniture isn’t really as easy as many presume. Furniture shopping has certain dos and don’ts—and if you want to be safe, then you need to actually keep them in mind.

Interested?

Here are some costly mistakes to avoid when buying industrial furniture:

Mistake #1: Not Doing Your Research First

If you want to find the right furniture pieces, then you need to actually have an idea on what you need. Otherwise, you might end up spending a lot of money on furniture pieces that won’t really bring you any good—and obviously, that’s not a good thing at all.

Try to determine what specific aspects of your work area need work on. Afterwards, try to see what specific furniture type can make it better. Do you want to make yourself more comfortable while working? If so, then an adjustable table might be a good idea. Or do you simply want something to get rid of the clutter lying all around? If so, then a good and sturdy cabinet just might do the trick.

Mistake #2: Not Having the Right Budget

Take note: Buying furniture is an investment. As it is, you need to make sure that you have enough finances to help you pick the right choice. Accordingly, this can help you avoid the problem of wanting a specific furniture piece so bad—but end up having to pass on it because you can’t afford it.

Mistake #3: Thinking Price is More Important than Quality

This is a common mistake that a lot of furniture buyers seem to commit.

Yes—price will always be an important consideration. However, you shouldn’t base your decision on price alone. You also need to make sure that the furniture you’re intending to buy actually has the qualities and attributes that you need. Otherwise, you might be spending a lot of money on repairs or maintenance later on. In effect, buying a cheaper, low-quality option might cost you a lot more in the long run.

Mistake #4: Not Looking for Different Options

There are many platforms available for your furniture needs. As it is, you should be prudent enough to see which specific option can bring the best benefits for you—and just take your pick.

Mistake #5: Dealing with Just Any Manufacturer

Remember: The furniture manufacturer you’re dealing with will play a huge role on how good your furniture will be. As it is, you should make it a point to ensure that you’re dealing with reputable companies that actually have the expertise and experience to back it up. This will help protect your furniture investment—and can help make sure that you’re getting the right furniture solutions.

The Main Reasons Why You Should Only Get RDM’s Industrial and Lab Furniture

June 26, 2015

We at RDM have always taken pride in our industrial and lab furniture.

Why?

Because we know that they can actually deliver the results that our clients are looking for.

From durability, aesthetics, efficiency and many other aspects—we have painstakingly ensured that people get what they want from their furniture solutions. And you know what? We have no plans to stopping…

So, do you want to know why you should only get your industrial or lab furniture from RDM?

Please read on…

We Have the Experience

RDM’s history spans almost 4 decades. The company was established in 1977 and continues to provide people with the specific solutions to their furniture needs.

With our vast experience, you can rest assured that you are getting furniture pieces that are designed with expertise—and crafted with the help of experience.

And there’s more…

Our Tradition

We at RDM believe that our clients deserve only the best. That is why we have invested our time, efforts and resources to ensure that our manufacturing procedures are up-to-date and will actually be able to produce the most efficient results possible.

When you do business with us, you can rest assured that you’ll be getting durable and efficient furniture pieces that are worth every penny. Our manufacturing standards are beyond reproach—which means you can be assured of efficiency and durability combined.

We Have a Wide Array of Furniture Pieces to Choose From

Do you need laminar air flow hoods? Flow benches? Or how about height adjustable tables?

Remember: When it comes to industrial or laboratory furniture—RDM is the name to trust. We have always made it a point to provide current and prospective customers with the specific furniture solutions they need and want, and we are always willing to go out of our way to ensure that happens.

Do you have specific or special needs or requirements? We can help you in that arena as well. We provide top-of-the-line custom furniture pieces, based on your specifications. In short: Just tell us what you need—and we will deliver.

Cost Efficiency

Despite our expertise and decades of experience, our furniture pieces are still reasonably priced.

Why?

We want people to actually have real furniture solutions. Our aim has always been about helping people out—and we intend to continue that tradition of excellence. You can be assured of that.

These are just some of the reasons why you should only get your lab and industrial furniture pieces from RDM. We are always here to serve you.

Tips on How You Can Save Money on Your Lab Furniture Purchases

June 17, 2015

Planning to buy lab furniture? Good! Lab furniture, as you may already know, can actually make your lab a lot more efficient.

But let’s face it though: Investing in lab furniture will mean having to shell out a good amount of money. However, that doesn’t mean you can’t be strategic about it. After all, with the right strategy and finesse, you can actually save money on your lab furniture purchases.

Interested?

Here are some tips on how you can make your lab furniture investment more feasible and economical:

Assess Your Needs Objectively

If you want to save money, then you need to invest only on those furniture pieces that you truly need. How? By assessing your needs—and being objective about it.

Don’t commit the mistake of buying furniture pieces just because they seem interesting to you. As much as possible, they must be able to address your specific needs. Do you need a flow hood to make your lab environment cleaner? Then get one. Or do you just need something to help make your lab more comfortable? In that case, a new table or sofa just might be what you’re looking for.

Set Aside the Right Budget

Your budget (whether you like it or not)—will be an important factor on the feasibility of your investment.

As it is, you need to set aside a reasonable amount of money that you can freely spend, in the event that you do find the right furniture. Accordingly, this will help you exercise the needed control and restraint on your spending—ultimately helping you save some money as well.

Use Different Platforms

Fact: There are now more than many ways to find the items you’re looking for. You just need to be strategic, and exert the needed time and effort to reach your set goals.

In fact, did you know that you can buy furniture online? Yes—many furniture manufacturers are now using the virtual platform to reach their market. So, you might want to take advantage of this trend to find what you need.

Tip: If you plan to buy items online, always make it a point to check on the seller’s reputation. This can help keep your transactions (and your money) safe.

Deal with the Right Manufacturer

Remember: As a potential buyer, you have the obligation to ensure that you’re making the right choice.

With that in mind, you should always exert due diligence in choosing your lab furniture manufacturer. Go for those who have the experience and expertise. Don’t just go for anyone, as they may only cause you more problems in the long run. The more experienced your manufacturer is—the safer your investment will be.

RDM: Keeping Up With Its Tradition of Excellence

June 8, 2015

For decades, RDM Industrial Products Inc. has been providing clients with exemplary products and services—and we intend to continue that tradition.

Ever since the inception of our company, our aim has always been about delivering on what our customers need. As it is, we continue to strive to provide furniture solutions that actually bring results.

Curious?

Here are some of the things you can expect when you work with us:

High Quality Furniture Solutions

When it comes to industrial and lab furniture, RDM is the name to call…

All our furniture pieces have been specifically designed to bring durability and high quality into the picture. Each has been made under very strict manufacturing standards and procedures, in order to ensure that our clients are able to get the furniture attributes and features that they truly need and want.

Affordable Rates

Despite our stringent efforts to bring quality lab and industrial furniture to our clients, you can reasonably expect our rates to be as reasonable as they should be. Our main focus has always been to help people, and we will do what it takes to continue that tradition.

From our flow hoods to our adjustable tables, you can rest assured that you will get furniture pieces that will not only fit with your preferences and needs—but your budget as well.

Customer Service

Our customers are very important to us. Hence, we always strive to ensure that all their needs are met accordingly. After all, without our customers, we wouldn’t have reached this far.

Do you need customized furniture for your special needs? Are you looking for something that can bring greater efficiency to your workplace? If so, don’t hesitate to contact us. We’ll be more than glad to give you what you need.

Our Reputation

For over 37 years, RDM has enjoyed the reputation of being an excellent provider of high quality furniture options. Our experience has made us even better at what we do, and we intend to continue bring people the quality furniture pieces that they truly deserve.

Yes—we are here to help you out. We have the skills and expertise to help bring you the required furniture solutions—at the right price. More importantly, we are always willing to take that extra step to ensure that you get furniture pieces that actually deliver results and benefits.

Looking for Lab Furniture? Here Are Some Common Mistakes to Avoid…

May 22, 2015

Purchasing good furniture for your laboratory can be a very good move, as it can actually lead to greater efficiency.

It is worthy to note, however, that a lot of people seem to commit certain mistakes when buying furniture. Unfortunately, that will not only lead to a wasted investment—but can also lead to safety risks as well.

So, what are the common mistakes to avoid when buying lab furniture? Please continue reading…

Mistake #1: Not Doing Your Research

If you really want to have the right furniture—then you need to make sure that you’re actually using the right one.

Study your lab. What items or furniture pieces does it really need? What specific features do you think can help make it more efficient? By knowing these details, you get to ensure that you’ll be making the right choice. Accordingly, this can help you save on time and effort—and money as well.

Mistake #2: Not Setting a Budget

Let’s face it: Buying lab furniture—whether it may be a laminar flow hood, lab cabinet or any other furniture type will mean having to spend some serious money. And if you are not careful, chances are it could mean a lot of wasted dollars on your part.

As much as possible, you should have a set budget in mind. This will give you a certain “spending limit,” which can help prevent you from overspending. Moreover, knowing your budget can help you pick the specific furniture types that will suit your preferences and your finances.

Mistake #3: Not Being Specific

Your laboratory has different needs and requirements—that specific lab furniture pieces can help resolve.

With that in mind, you should make your search more specific. Doing a mere “general” search for furniture will do you no good. Again, look for specific furniture pieces that will help solve specific problems. The more specific you are with your search, the easier for you to find the appropriate furniture pieces that you actually need.

Mistake #4: Dealing With Just Any Manufacturer

Fact of the matter is: Your furniture manufacturer will play a huge role on the efficiency, feasibility and quality of your lab furniture. As it is, you should always make sure that you are dealing with people that have the required expertise and skills.

Remember that laboratory furniture is a special type of furniture. Hence, you should make it a point to seek help from the right people. After all, you deserve furniture pieces that can actually bring you the required solutions.

Check for the manufacturer’s experience. How many years has it been in service? Does it have good customer feedbacks? By knowing which is which, you get to ensure that you’re getting real furniture solutions (at the proper rates)—and services worthy of every penny of your furniture investment.