|
|
 |
|
Test Equipment
|
|
Item:
|
Description: |
RT-1000
Standard Resistivity Tester
Meeting 20/20 Standards
Quantity:
|
Humidity and temperature affect resistivity so
they must be tested. The Ohm-Stat® RT-1000
tests resisitivity, humidity and temperature of all conductive,
antistatic and static dissipative surfaces for electrical
resistivity/resistance according to the EOS/ESD CECC, ANSI,
ASTM, UL, NFPA, Military, and EIA test procedures.
The RT-1000 includes:
- Two 5lb. 2.5" probes with handles
- Two 3" parallel surface resistivity probes
- Dissipative chair test probe (meets ANSI/EOS/ ESD
Standard 12.1)
- Earth ground probe
- Garment clamps (conforms to EOS/ESD 2.1 standard)
- Concentric ring probe available
- Foam lined carrying case
|
|
|
The Ohm-Stat™ RT-500 Megohmmeter
measures Surface Resistivity using parallel electrodes and
concentric rings. Tests Resistance To Ground (RTG), Resistance
Between Two Points (RTT) and Volume Resistance using two 5 lb.
2.5” disk probes.
Ohm-Stat RT-500 tests each sleeve of a garment for continuity
in addition to performing dissipative seating tests. The RT-500
can also test shoes, heelgrounders, and wrist straps with
optional accessories. Conforms to ANSI/EOS/ESD (S4.1, S7.1,
S12.1, S2.1), EN 61340.5.1, ASTM-F150, NFPA 99A, and ASTMD257
standards.
The Ohm-Stat RT-500 Megohmmeter is designed to quality
inspect incoming materials such as floor finishes, floor mats,
table mats, conductive floor tiles, work surfaces, paints, bags,
wrist straps, common point ground cords, footwear, packaging
materials, clothing, and ESD chairs in static controlled areas.
|
CM-1700
Constant ESD Monitor
(Monitors Wrist Strap & Person)
Quantity:
|
- 100% continuous monitoring
- Works with standard one conductor wrist straps/cords
- New technology -capacitance/impedance hyper technology
- NIST calibration included with certificate
- Visual LED, audio piezo sound
- AC powered or 9 volt battery operated
- Off/On switch
- Set points can be adjusted for impedance of wrist
straps, capacitance of person and resistance of mats
- Works extremely well with
Ultimat ESD Rubber except Ultimat White
- Size: 3 in x 2.75 in x 1 in.
- Mounting: hook/loop and screws.
- Safe limits: .75-1.2 megohms. Inpedance can be adjusted
according to weight and size of operator.
- Fail limits: Below .75 megohms and over 1.3 megohms.
- Visual alarm: red-fail, pass-green.
- Audio alarm: piezo buzzer.
- Operation:
- active when switch tuned on.
- Inactive when power switch turned off, cord on docking
snap, wrist strap on and green piezo on.
- Wrist straps connected to ground even if monitor turned
off.
- Trigger impedance not changed by change of incoming
voltage.
- Power: 110 volts or 9 volts battery with low power LED.
- Socket: banana plug.
|
CM-1701
Constant ESD Monitor
(Monitors Wrist Strap, ESD Mat, & Person)
Quantity:
|
- 100% continuous monitoring
- Works with standard one conductor wrist straps/cords
- New technology -capacitance/impedance hyper technology
- NIST calibration included with certificate
- Visual LED, audio piezo sound
- AC powered or 9 volt battery operated
- Off/On switch
- Set points can be adjusted for impedance of wrist
straps, capacitance of person and resistance of mats
- Works extremely well with
Ultimat ESD Rubber except Ultimat White
- Size: 3 in x 2.75 in x 1 in.
- Mounting: hook/loop and screws.
- Safe limits: .75-1.2 megohms. Inpedance can be adjusted
according to weight and size of operator.
- Fail limits: Below .75 megohms and over 1.3 megohms.
- Visual alarm: red-fail, pass-green.
- Audio alarm: piezo buzzer.
- Operation:
- active when switch tuned on.
- Inactive when power switch turned off, cord on docking
snap, wrist strap on and green piezo on.
- Wrist straps connected to ground even if monitor turned
off.
- Trigger impedance not changed by change of incoming
voltage.
- Power: 110 volts or 9 volts battery with low power LED.
- Socket: banana plug.
|
|
|
- 100% continuous monitoring
- Works with standard one conductor wrist straps/cords
- New technology -capacitance/impedance hyper technology
- NIST calibration included with certificate
- Visual LED, audio piezo sound
- AC powered or 9 volt battery operated
- Off/On switch
- Set points can be adjusted for impedance of wrist
straps, capacitance of person and resistance of mats
- Works extremely well with
Ultimat ESD Rubber
- Size: 3 in x 2.75 in x 1 in.
- Mounting: hook/loop and screws.
- Safe limits: .75-1.2 megohms. Inpedance can be adjusted
according to weight and size of operator.
- Fail limits: Below .75 megohms and over 1.3 megohms.
- Visual alarm: red-fail, pass-green.
- Audio alarm: piezo buzzer.
- Operation:
- active when switch tuned on.
- Inactive when power switch turned off, cord on docking
snap, wrist strap on and green piezo on.
- Wrist straps connected to ground even if monitor turned
off.
- Trigger impedance not changed by change of incoming
voltage.
- Power: 110 volts or 9 volts battery with low power LED.
- Socket: banana plug.
|
|
|
The digital FM-1125 ESD Field Meter provides
fast and easy precision measurements. The unit is grounded
through its conductive case, the need to wear a grounded wrist
strap is eliminated. Measurements are dependent on distance to
the meter using a unique spacer.
- Digital display is updated every three seconds
- Non-contact
- Indicates voltage and polarity
- Power on/hold and zero buttons
- Easy to read 3.5 inch LCD display
- Range: 1-80,000 volts
- 1 inch spacer bar
- 9 volt battery operated
- leather case included
- conforms to EOS/ESD 20.20 Specs
- Checks for class zero conformance
- NIST certificate included
|
|
|
The CT-8900 individually and simultaneously
tests, prints, stores, and e-mails each wrist strap and heel
grounder resisitivity value in less than 3 seconds. Used at
manufacturing companies internationally and domestically, it
offers adjustable limits, exact resisitivity readings, unique
report generation groups, versatile networking options, an
expandable employee log of 30,000 and is foolproof.
It accepts magnetic stripe, barcode, Motorola, Indala , HID,
HID iClass, Casi-Rusco, AWID etc. ID cards as well as keyboard
entry. Complete with user-friendly software, this unit is the
most accurate and thorough combination-data logger available on
the market. Ideal for EOS 20/20 class zero and RoHS specified
areas.
- Once or twice per day employee failure exception reports
- Monthly, daily, entire log
- ESD training certification expiration
- Employee attendance/vacation
Logs are easily imported into spreadsheet/database programs
- Accepts and displays international dates/times
- Software and employee information can be password
protected
- Able to prevent unauthorized entry without proper ID/ESD
certification
- Can be upgraded to allow electronically locked doors to
open, or bells to ring, when users pass a test
|
CT-8700
Combination Tester without Computer Interface
Quantity:
|
| The performance and
accuracy of the industry exclusive
CT-8900 Combo-Tester above, without the computer
interface. Don't pay for features you don't need!
The CT-8700 is a combination tester that can test
wrist straps and heel grounders simultaneously and
individually. The meter then displays a pass/fail using
set specifications with different colored lights and a
buzzer. This tester conforms to both US and European
CECC standards and specifications. It accepts domestic
and foreign wrist straps, plugs, 4mm or 10mm snaps and
dual stereo plugs.
The CT-8700 individually and simultaneously tests
each wrist strap and heel grounder resisitivity value in
less than 3 seconds.
All CT-8700 meters come with a 1-year warranty
|
|
|
|
Durable stand to be used with
CT-8900,
CT-8700 and
FP-8755 foot plate accessories above.
- Organizes unit, cord, and power supply to make work area
safe and aesthetically pleasing.
- Heavy duty welded steel
- Powder coat finish
- Enables meter to be used in middle of the room
- Includes channel to hide all wires and cords
|
|
|
|
